EVO1000W-1 Greenhouse HID Ballast (Electronic, White)
EVO1000W-1 Greenhouse HID Ballast (Electronic, White)
Item name: EVO1000W-1 Greenhouse HID Ballast (Electronic, White)
Series: EVO High Efficiency
Model No.: EVO1000W-1
Lamp Type: MH / HPS
Certifications: CE, FCC, CSA-CUS
Warranty: 2 years
Scope of application: Road, sports, square, station, quay, factory, etc
Packing: Neutral Packing / Customized Packing (with 120V 6ft Input Power Cable)
EVO serial electronic ballast (HID) is developed successfully in Germany, and then put into production in China. It is new type electronic ballast for high-pressure sodium lamps (HPS), metal halide lamps (MH) and high pressure mercury lamps (MV). It’s a new generation of green lighting products and has the advantages of energy saving, almost no noise electric wire netting, high-quality illumination support.
Technical Parameter (HPS& MH Lamp)
Model No. EVO1000W-1
Input voltage 90V~260V
Frequency 50Hz / 60Hz
Input current 9.16A / 4.38A
Power factor ?0.98
Input power 1150W
Start current About 2.1A
Operating voltage range 90V~260V
Total harmonic distortion ?10%
Operating temperature -40?~+60?
The EVO electronic ballasts have the following superior characteristics.
1. Wide working voltage range: 90V~260V, it is applicable to the fluctuating voltage of power supply;
2. Small starting current: The start current of EVO series electronic ballast is small, which can extend the life and reduce the cost of first installation.
3. Low start voltage: ?90V
4. Energy efficient: At least 3% of the lighting efficiency improvement; at least 15% of the power savings (compared with magnetic ballasts)
5. High power factor: ?0.98
6. Constant power: support fluctuating voltage 90V~260V; output power is constant; guarantee stable lighting quality and intensity of illumination of lamp.
7. High quality illumination: frequency ? 24KHz, light source does not flicker, for the Sports, Street, and Commercial lighting.
8. Low harmonic content: THD ? 10%;
9. Protection: breaking circuit, short circuit, hot protection;
10. Simple installation: no need other boot; no need external compensating capacitor.
Power Factor Correction (PFC)
Because of PFC technology, its input current is complete sine, and power factor is greater than 0.98. Therefore, it does not interfere with the power supply. The constant power system keeps the lamp in the invariable power and basically voltage fluctuate supply environment.
When power on, AC (Alternating Current) 90V~260V goes through a full-wave rectification, and PFC circuit filtering, and then it’s converted into DC (Direct Current) 400 volts, and obtains high frequency 200 to 300 KHz. After that, a half bridge circuit convert it back into the alternating current. The resonance circuit produce a high voltage pulse, and ignite the lamp.
This ballast has breaking circuit, shorting circuit, and hot circuit protection. Another case is in power supply or the lamp is shut in a short time. After light goes out, the ballast automatically restart about every 40 seconds. If the boot fails 3 times, it’s recognized as a circuit fault. The ballast comes into the automatic shutdown to protect the security of system.
The ballast is used with HID lamps. The trigger function is integrated inside. It has excellent features of high efficient, safe, constant output power etc., and can be used in such places as road, square, station, quay, factory, etc.
2. Installation Diagram
Please install the circuit according to the diagram and guarantee the reliable connection for each point.
Please use the cable which can bear voltage ? 6KV between the ballast and the light. The length should not exceed 1 meter. Make adjustment according to the installation and specific demands.
1. To ensure the best working state of light source, the ballast should be used together with the corresponding related bulb.
2. The instantaneous output voltage may reach above 3KV (up to the end of light). When not in use, turn off the power by maintenance.
3. The input rated voltage-frequency is 120V / 240V, 50Hz / 60Hz, and the operating voltage range is 90V~260V. Please don't try to use the ballast in the exceeding voltage range.
4. Environment temperature should be -40?~+50?. If the temperature is exceeding this range, the bulb can’t start normally and the ballast life-span will be shortened.
5. The ballast could restart after the lamp is cooled. Because of the different characteristic between high-pressure sodium lamp and metal halide lamp, there is a time difference to restart the device. The sodium lamp may need to wait 1
Founded in 2002, Maker Lighting Company Limited is specialized in the design, production and sales of high quality Plant Grow Lighting, Aquarium Lamps, LED Lights, HID Bulbs, HID Ballasts. As a professional OEM & ODM lighting supplier in China, we gained high reputation from customers all over the world.
Our factory covers over 30,000 square meters. We have the first-class lighting design team of engineers and professional production lines. Maker Lighting Manufacturer has obtained CE, ROHS, UL, CSA and other international certification. Over the years, we insist on strict quality control and the pursuit of marvelous crafts all the time, hoping to become your first choice of OEM / ODM lighting supplier.
Maker Lighting has a wide range product line, including HID Grow Light, HID Ballast, LED Grow Lamp, CFL Plant Grow Light, HPS Bulb, MH Bulb, HPM Bulb, LED Ceiling Light, LED Spot Light, LED Bulb, LED Soft Tube Lamp, etc. In 2009, Maker Lighting set up our sales center near to the Guangzhou New Airport, to provide the vocational, convenient and individual service for (the) global customers.
The mission of Maker Lighting is to satisfy customers’ individual needs with maximum capacity! Maker Lighting has been adhering to customer-centric, sustainable and innovative vigor, determining to create the maximum value for all customers. Every customer is the idea “Maker”, who can create your favorite professional lamps by Maker Lighting factory.
Your satisfaction is our greatest pursuit! We sincerely look forward to the cooperation with you in the near future.
Maker Lighting Company Limited
The professional Lighting Supplier!
ISO 9001 &14001, CE, RoHS, UL Certificated
PRC Tel: +86-020-22078445
Factory Address: Guangzhou, China
HK Address: UNIT 04, 7/F, BRIGHT WAY TOWER 33 MONG KOK RD, KL, HK
Send Supplier a Message
Not a Member?
Already a member? Sign In