Introduction of Aerial Photo Drone (APD) Oblique Photograph System
Packaging and Delivery
Traditional aerial photography can only shoot objects from vertical angles, while oblique photography carries multiple sensors on the same platform. At the same time, the oblique photography collects images from different angles, such as vertical and side viewing, which effectively makes up for the limitations of traditional aerial photography. So the Aerial Photo Drone (APD) Oblique Photograph System can be defined?with the APD as the flight platform, the aerial image acquisition system with tilt camera as mission equipment.
1. The performance requirements for flight platforms.
At present, there are various kinds of aerial photo drone in the market, which can be divided into internal combustion engine power and battery power according to the power system. It can also be divided into fixed and rotors (single rotor, multi-rotor) according to the flight modes. Because of the vibration of the flight platform itself, the battery power is better than the internal combustion engine; in the operating efficiency and endurance time, fixed wing is superior to rotor; in flight stability, the rotor is superior to the fixed wing. Because of the different uses of drones, their performance standards are different. A mapping APD requires a higher flight standard, which can be defined in terms of payload, cruising speed, practical lift, endurance, safety and wind resistance levels.
? The minimum load of the aerial photo drone is 2 kg;
? The multi-rotor cruising speed is greater than 6 m/s, and the cruising speed of fixed-wing APD is greater than 10 m/s;
? The power endurance time of the battery is longer than 25 min, and the internal combustion engine's power life is longer than 1 h.
? The wind resistance requirement is not lower than the level 4 wind speed level;
? The practical lift of the APD can reach more than 1000 m, and the altitude is not less than 3000 m.
2. Performance requirements of oblique cameras
In the specification of low altitude digital aerial photography (CH /Z 3005 - 2010), the aerial photographs of Surveying and mapping, that is, the photo tilt angle of vertical photography, are as follows: The dip angle is not more than 5 degrees, and the maximum is not more than 12 degrees. The ability of the existing aerial survey software has been greatly improved. On the basis of this standard, 15 degrees above the angle of tilt can be classified into the category of tilt photography. With the development of oblique photography, oblique cameras no longer limit the number of cameras. The key technical indicators of oblique cameras are the ability to acquire images at different angles and the breadth and depth of single sorted operations. It includes five lens, three lens, double lens, multi lens camera, and a single camera system that can adjust the photographic angle of camera. In the supervisor standards of the APD, the requirement of aerial camera pixel is no less than 35 million. In oblique photography, it is not necessary to restrict the pixels of a single camera, but the control of the pixels that are acquired by one exposure. The performance requirements of oblique cameras can be limited from the aspects of image acquisition capability, operation time, exposure function, endurance time and POS recording function.
? The higher pixel of one exposure, the better of the oblique photography effect , but the single lens is not less than 20 million pixels, and the first exposure is not less than 100 million pixels when consider the costs of the equipment;
? The operation time must be at least 90 min, preferably it has the ability with all-weather operation.
? It has the fixed-point exposure function which ensures the images overlap degree can meet the requirements.
Established in 2005, Shenzhen TitanFlying Technology Co., Ltd (TTF) is located in Shenzhen Univercity Town, known as the silicon vally of China.
TTF Technology is a high-tech enterprise and professional Aero-Model manufaturer that unifies product design, research&development, production, marketing and customer service. Our main product is the UAV Power System, Gimbal System and PTZ Control System.
We have a whole machining industry chain. All our products, from the materials processing to completed products, were manufacturered by ourselves. Thus the quality and the consistency can be well controlled and always be the top of the industry. Besides the standard edition, we also supply customer-exclusive edition, which has its own SN for each product. (Support all your requests)
""Touch The Future"" is the company slogon of TTF Technology, and we know that we cannot achieve this goal without your support and attention. So we will continuously provide you our best-quality products with super material and unique technology.
Send Supplier a Message
Not a Member?
Already a member? Sign In